REVscene Automotive Forum

REVscene Automotive Forum (https://www.revscene.net/forums/)
-   Island Off-Topic (https://www.revscene.net/forums/island-off-topic_147/)
-   -   Toyota supra chat thread (https://www.revscene.net/forums/39394-toyota-supra-chat-thread.html)

NashMan 06-23-2003 12:06 AM

rob you are the getto master to bad you got to do it all over again this time do it right hehehe



i had fun it was blast nice meeting you guys now you guys got to come down here

fuzebox 06-23-2003 08:06 AM

Quote:

Originally posted by NashMan
rob you are the getto master to bad you got to do it all over again this time do it right hehehe

I did do it right you bastard!@$ I dunno wtf is the problem... maybe I didn't torque the turbo bolts tightly enough? Stupid box wrench was too short and I've got like a bruise in my palm from torquing.

NashMan 06-23-2003 08:40 AM

what i ment was gasket's the exhuast manofold gastket chould not seal cause it crush based gasket just like head gasket pretty much


see the rings then selfs crush to seal the other edge crap jst keeps it form not leak oh yae did you pu the exhuast gasket ont eh right way

there is littel tab ont eh top of the gasket ti should be at the back of the mor not the front or it on back words


but i think i cheak that befor you turqed

NashMan 06-23-2003 08:47 AM

ok we got ot start to plan this supra meet i was thinking of haven it the same time the toyota meet is happing so ti will still get alot of car but they be all toyota any wya

!Mpower 06-23-2003 10:20 PM

limp clutch
 
i guess its time to change it.. i saw a spurt of fluid coming from the seal of the master cylinder by the firewall area.

mann.. those two bolts holding the clutch m-cylinder is a PITA, mainly the one on the kickpanel side :o so close too.. i just need a really deep socket (13 or 14mm?) now

NashMan 06-24-2003 01:52 AM

Re: limp clutch
 
Quote:

Originally posted by Mpower
i guess its time to change it.. i saw a spurt of fluid coming from the seal of the master cylinder by the firewall area.

mann.. those two bolts holding the clutch m-cylinder is a PITA, mainly the one on the kickpanel side :o so close too.. i just need a really deep socket (13 or 14mm?) now


yae the4y can be a pain to install but in the end it all worth it



but remmber to make the rod as long as possilbe on the new master cycl dilder or it will not move back to place cause the spring is in the master t self and not on the pedale liek most cars

!Mpower 06-24-2003 11:14 AM

got beneath the dash.. managed to remove the pin and clip off last night.

after work today, i'll try to get at the two cylinder nuts.

btw is the bleeder bolt hard to find? i heard it's a 10mm one and accessible from underneath..

NashMan 06-24-2003 11:26 AM

the bolts are easy to get at if you have the small renches and deep socket it easy

just pain in the ass to sit int he seat up side down wiht you feet sticking up in the air othe then that easy as hell


bleed again is easy it just little nib off the slave just lossen it and bleed


if you want me to tell you how to bleed just ask and how to ajust the clutch pedale

NashMan 06-24-2003 05:12 PM

hey keeagin whos the car going now heheheh boost leaks are gay don't you think

!Mpower 06-25-2003 07:04 AM

Quote:

Originally posted by NashMan

bleed again is easy it just little nib off the slave just lossen it and bleed

if you want me to tell you how to bleed just ask and how to ajust the clutch pedale

Bleeding will begin later today! hope the clutch will pump again.

is the m-cylinder rubber seal strong enough? cuz i yanked on it once during the install as i was fitting it thru that narrow hole in the firewall ...realizing that i didnt set the piston long enough

NashMan 06-25-2003 07:26 AM

Quote:

Originally posted by Mpower
Bleeding will begin later today! hope the clutch will pump again.

is the m-cylinder rubber seal strong enough? cuz i yanked on it once during the install as i was fitting it thru that narrow hole in the firewall ...realizing that i didnt set the piston long enough


should be fine it more of dust cover then any thing

!Mpower 06-25-2003 09:30 AM

it sure is nice to have our car's manual online :D
though, the visuals are sometimes not detailed enough, but i'm not complaining!

http://www.cygnusx1.net/supra/library/TSRM/cl/CL_04.gif

NashMan 06-25-2003 10:45 AM

you going to come to the supra meet man i forget you name again i bad with names i all ways for get them :p

_supras_ 06-25-2003 11:01 AM

hah
 
Quote:

Originally posted by NashMan
hey keeagin whos the car going now heheheh boost leaks are gay don't you think
tell ya one thing...THeres a big differnce now! 9psi is fun :)
Hrm..think I could borrow that jack for a day? Mine is crappin out..fuckin hand jacks.

NashMan 06-25-2003 03:07 PM

i don't know it kinda in use right now it under my pos brown car

Enraged 06-25-2003 03:16 PM

go to lordco and buy the $25 special jack :)

i want the $250 pimp jack though, lift my car 2 feet off the ground with 2 pumps of the handle...

Paradox 06-25-2003 04:29 PM

my jacks a tad big, gets the job done well tho

think i paid like $125 for it from NAPA, cant remember now

Enraged 06-25-2003 05:10 PM

not car related, but i got my new pc parts in, and im pickin up some plexiglass for it tomorrow. hopefully get it up and running in the new custom case on saturday

NashMan 06-25-2003 06:21 PM

Quote:

Originally posted by Enraged
not car related, but i got my new pc parts in, and im pickin up some plexiglass for it tomorrow. hopefully get it up and running in the new custom case on saturday


all way's remmber when jacking up you pc when going to work on it use jack stand cause it may fall lol hehhheheh i am funny man an't i :D

Paradox 06-25-2003 07:16 PM

Quote:

Originally posted by Enraged
not car related, but i got my new pc parts in, and im pickin up some plexiglass for it tomorrow. hopefully get it up and running in the new custom case on saturday
killer, how far have you gotten with making the case?

have any pics?

NashMan 06-25-2003 07:55 PM

i cumsived my case back in the day it was the pimp thignto do but now i can care less

Paradox 06-25-2003 09:27 PM

you circumsized your case?! :p

fuzebox 06-25-2003 09:52 PM

Quote:

Originally posted by Paradox
you circumsized your case?! :p
No, he had himself circumsized in case.

NashMan 06-25-2003 11:01 PM

that was suppost ot be custom ized my case hehehe

!Mpower 06-26-2003 09:05 AM

clutch update
 
Alright... back in action! Tightened all bolts on the master cylinder. Then, continued to bleed it for a good 20min. Spent a good couple minutes determining where that bleeding nipple was : d

Pedal kinda seems a tad lighter now and more precise at the 'engaging point' ~ that sound ok?

had a couple guys lend a hand yesterday, thats always nice.. then went for wings after :D


All times are GMT -8. The time now is 02:13 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
SEO by vBSEO ©2011, Crawlability, Inc.
Revscene.net cannot be held accountable for the actions of its members nor does the opinions of the members represent that of Revscene.net