time to organize a supra meet/cruise on one of these sunny days we are having..
ryan finish it up already!!

are n/a's welcome:D?

well i going to plan a big meet for so summer or close to it plus the guys from van cover will coming to as well

better the the last one we had last last summer

every thing is welcome to come

hey ryan, you know those studs in the shifter base... what about using a bolt and a threaded standoff? mcmaster sells stainless steel round standoffs, just need to threadlock the onto the bolt thats already in the base (might have to change the size of the bolt for the next batch). http://www.mcmaster.com/#91125a451/=nrnoi

my buddy is parting out a white with red interior 88 supra in van if anyone needs parts... driveline is spoken for

white? maybe a hatch for murray?

bleh, got the dash all out, what a shitty. Those instructions on SOGI need to be edited, had me looking for bolts, nuts and screws that dont exist and unhooking things that weren't necessary :mad: stupid heater cores.

the only good news is the heater core has a good sized hole, better than doing all that for some pussy little dribble. happy I didn't damage the pipes too badly, only the passenger side is a little out of round. The absolute worst part of this was getting the dead pedal screws off, fuck you Toyota and your phillips head screws, probably 45 minutes worth of beating them with my hammer driver until I smartened up and drilled the heads off.

$$$$$$$$ says $1650 for a 7MGTE longblock shipped, I dont know if thats good or bad but considering id be doing a full rebuild on it before it went in it would be more expensive than an 18 year old, $16/hr can afford.

I'm looking at over $3000 in parts to rebuild my VG30 + labour to assemble the pistons/valves into the short-block. Mind you that isn't a stock rebuild, but still....

PS - I'm 20, a full time university student, and make less then $16 an hour :


So don't complain, you could be in my boat, haha.

when is Don coming over to the island? he was going to bring me that 89+ hatch.

who drives the all black turbo supra?..i saw it last night on veterans and sooke road around 830..had different coloured head lights

i gave you a pm call him or he wonte bring it over simple as that he called me again last night to see if i have talked ot you i made it simple for him you call him or you don't you decide

that still wonte come with every thing you need that is another sad part

i know some one selling a holes 88 trubo convertion right now as well his name is toshio

ouchie kicks ass.

http://photos-a.pe.facebook.com/phot...44848_5634.jpg

never again, (btw what can I do with that steering wheel, its nasty)

http://photos-b.ak.fbcdn.net/photos-...83209_5147.jpg
daily driver for the last 3 months.

Heading over wednesday. Anybody need anything?..lmk before tuesday.

Don 1(604)728-8248

if it is nasty and you hate wheel covers just rip off the leather it will still look good under it and still blue

i have grant one here wiht hub if you car to upgrade i some were in my parts room if remmber right

got spiffy cams or soild motor montes

grrr my front end is clunk clunk clunking.... only when i steer sometimes.
coming from the front drivers side corner.. thinking lower ball joint and will check this weekend... maybe steering rack??
and it is pissing out a lot of P/S fluid from the side that the pump is on...
grrrrrrrrr

I found 2 spare window regulators in my garage a few days back. Both comes with the motor, track, electrical bung and everything else needed - anybody need them?

ball joint and high persure line are you issues

ps i whould nto drive on bad ball joint for long cause wel you wheel will pop and fold causeing alot of damage

just do the simple bord test

whats the bord test?

No cams other than my personal TRD's but solid mounts I may have I'll take a look. I had (2) sets made when I needed a set. 89+ fitment. $115.00 each is what I paid to have them made at Smith Industries.

Renthal I have a hi pressure line (new condish) I bought from a friend. $50.00

it's easy jack up car place on jack stand so it sit's frim

take pone bord place it under the wheel take block of wood put under neat the bord step on bord if you feel a slight give you wiggle the ball joint is bad it's pretty easy

115 for hunk of meatl with hole in it hummm don i can pay that much for hunk of auminin with hole in it

anyone want a celica? looking at maybe buying a new car shortly.