|
Quote:
id still confront them though |
Had a custom H pipe made and installed by Rise. Car sounds great now compare to the straight set up I had with no crossover pipe. **** :thumbsup: |
Vacuumed/Leather detail/windows. :fuckyea: super clean inside! :D @Supa: 3rd time?! Fuck I wouldn't be going back again. |
Tryed to figure out how the hell ford sync works... |
Installed my old deck in my new car and wired up the bluetooth. Broke a clip in the a-pillar cover though :okay: |
Remove my CAI and put stock intake back on... running stock class in autocross |
uninsured, washed, stored. |
Quote:
Quote:
What i did with mine, had to do it twice though tremclad didnt stick so i redid it with por 15 http://i589.photobucket.com/albums/s..._00/009-61.jpg http://i589.photobucket.com/albums/s...00/003-109.jpg http://i589.photobucket.com/albums/s..._00/008-70.jpg |
Quote:
|
Getting a gt wing shipped from ASR carbon factory. Can't wait to install it. |
Paid some people to do some shit. |
Raped 2 trannies to make one good one. :troll: Finally installed, just need to button up the exhaust and refill the fluids tomorrow. |
Quote:
I'll send you a PM with contact info if you'd like to have this issue cleared up and fixed. The issue has already been brought up with them and they're more than willing to speak with you on the matter. |
Installed exhaust, new shifter bushings, filled tranny fluid, checked all other fluids, wired stereo, replaced sideview mirror, washed car, test drove, cleaned up my mess. |
washed it! white cars always look stunning freshly cleaned ........ for the minute it stays clean :( |
I brushed off snow on my car....... Oh alberta.... |
|
gotthe dimmer working on my deck, lubed up sway bar bushings and doused endlink bolts with penetrant. Posted via RS Mobile |
Changed manual tranny fluid, lubed shifter bushings, waited for more than an hour at a junkyard for a wheel, washed and waxed the car, now waiting at tire shop to get tire mounted on the new rim. Posted via RS Mobile |
Threw the coils back on, oil change and started to sand down the front end for paint Posted via RS Mobile |
removed my 'limo' tint. When i purchased this car, it had this super dark 5% tint on rear 3 windows...so i took a handheld steamer ($40 at walmart)...steamed up windows at high heat.. began peeling the tint.. the glue would pretty much melt with the heat of the steam and basically rubs right off. would have cost me $150 to get it done at whatever tint shop. Plan is to tint a bit lighter next spring but this dark stuff look was way too dark for my liking. |
Good choice. I think dark tint on anything smaller than a 7 series takes away from the cleanliness (and drivability) of the car. |
turned the boost down cause the clutch isn't holding the torque anymore :( adjusted afr&timing sent an oil sample for analysis to blackstone labs |
sold my set of VMRs. http://distilleryimage1.s3.amazonaws...38016265_7.jpg back on stocks/allseasons till spring rolls around and i get my next set :| http://distilleryimage3.s3.amazonaws...0a1d03b6_7.jpg |
^ I actually like the stock look and were you on SW marine drive last night around 12am? |
| All times are GMT -8. The time now is 06:26 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
SEO by vBSEO ©2011, Crawlability, Inc.
Revscene.net cannot be held accountable for the actions of its members nor does the opinions of the members represent that of Revscene.net