Changed my oil today and diagnosed the my dead right speaker.
Turned out the the strain relief on the wires popped off from the door and loosened up the connectors.
I'm also brainstorming ideas to invisibly mount my old speakers in the rear of my ef hatch.
Posted via RS Mobile

Went wheeling
https://fbcdn-sphotos-a-a.akamaihd.n...83457186_n.jpg

Then got stuck
https://fbcdn-sphotos-c-a.akamaihd.n...35164222_n.jpg

And broke some stuff
https://fbcdn-sphotos-h-a.akamaihd.n...61228986_n.jpg

^ holy sh*t

That push bar bolted to your frame ?

Welds give or did the bolts shear ?

PO only had two bolts holding it on, and we were pulling parallel to the bolts, sheared all the threads. Stupid PO for halfassing his shit and stupid me for not checking it. Just gotta weld it on and call it a day.

Did an oil change.

Peeled off some plasti dip that got messed up from contact with brake cleaner.

http://i50.tinypic.com/bgwsgh.jpg

http://featherfiles.aviary.com/2013-...aeafdbf8b8.jpg

Got my gloss black grille today.

http://i1.minus.com/jbd5rszhZys9DD.jpg

Haven't work on my car in a long time :okay:, and I hate working on these grille.

http://featherfiles.aviary.com/2013-...67b4694524.jpg

installed new o2 sensor and exhaust manifold gaskets. Subie rumble with no CEL :megusta:

Insured my FRS yesterday after the winter. Got new Dunlop Z2 tires put on last night and Subaru BRZ diffuser installed this afternoon (the little plastic thing underneath the muffler tips)

https://fbcdn-sphotos-e-a.akamaihd.n...17154085_n.jpg
https://fbcdn-sphotos-a-a.akamaihd.n...70703053_n.jpg

I want a set of Z2's. :megusta:

how are the Z2s? I have Z1's :megusta:

went to install a ueo rear strut bar, requires 3 holes to be drilled at each side of the strut tower, the seam sealer would need to be stripped off at the contact points. also the rear end of the bar bolts to the rear bumper mount replacing the original bolt that holes it up. after 27 years the bolts have found themselves a nice home and decided not to leave without a fight

http://i349.photobucket.com/albums/q...ps635a81cc.jpg
http://i349.photobucket.com/albums/q...ps984effef.jpg

... im never going hit 500 posts at this rate

Never got a chance to try Z1's. But Z2's are surprisingly good in the wet weather today.

installed my o2 today...learned that there is an o2 nut in place....initially i though i bought the wrong part....

Put on the spare after i found out i got keyed and tire slashed/poked. :okay:

S2000 antenna :wiggle:

http://i.imgur.com/25C1L9n.jpg

More work done on my engine today

put the flywheel on first
https://fbcdn-sphotos-b-a.akamaihd.n...93357809_n.jpg

then clutch disc
https://fbcdn-sphotos-h-a.akamaihd.n...86899859_n.jpg

and pressure plate
https://fbcdn-sphotos-g-a.akamaihd.n...41581754_n.jpg


Also removed EVERYTHING at the front of the car so the engine and tranny should slide in with ease. that will be tomorrow
https://fbcdn-sphotos-h-a.akamaihd.n...74978432_n.jpg

Been a while since I've given her a proper wash, so I did that today.
http://i45.tinypic.com/54ssr8.jpg

cut 1 out of 4 rusty sections of rocker panel off my crx

http://i282.photobucket.com/albums/k...ps2552ed5e.jpg

then i cut a replacement piece off my donor car. TIP: use arrows so you know which side of the line to cut on!

http://i282.photobucket.com/albums/k...ps2912e6e0.jpg

but even with arrows, i still fucked up so i had to do it again.

http://i282.photobucket.com/albums/k...pse2e6ddf0.jpg

piece held in place with a magnet

http://i282.photobucket.com/albums/k...psba66d840.jpg

didn't weld it since it's too windy and the welder is running out of gas. i'll do it another day. so started working on the largest piece that needs to be replaced.

http://i282.photobucket.com/albums/k...ps959096ad.jpg

http://i282.photobucket.com/albums/k...ps4c5d948a.jpg

once i've cut the old piece off the crx i'll work the replacement piece into the correct shape/size.

played with suspension settings, lowered a bit, put spacers on :notbad:

What did I do to my vehicle today? More like what did other people to do my vehicle :okay:

Some guy in his F150 scraped my car when he was trying to park it with his running board.. of all things. Now my alignment's screwed too :fuuuuu:

http://i48.tinypic.com/2j9qg4.jpg

He wants it settled privately because he says it's not that big of a deal, but I'm leaning towards claiming this

claim it, shit like that can get expensive

Claim that shit. He can pay ICBC back if he doesn't want his premiums to go up.
Posted via RS Mobile

Claim it. He can pay icbc out later.

Who cares what he wants, unless he's stupid enough to pay way more than the damage is worth. Call ICBC and get it dealt with.