You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
The banners on the left side and below do not show for registered users!
If you have any problems with the registration process or your account login, please contact contact us.
OK, so after the 5th time going to the shop that installed my coils to get rid of rear squeaking, there is still squeaking, and I'm like
Chronological order of events:
1. coils installed along with all new OEM parts everywhere, not a single old part was used
2. after driving for the first time in the rain about 2 weeks after installing the coils, squeaking started in the rear after the car dried out
3. went back to the shop got them to regrease everything
4. squeaking was there as soon as I left the shop parking lot
5. went back in for regreasing
6. squeaking happened again as soon as I left the shop parking lot
7. went back in for regreasing and they reassembled the rear strut assemblies
8. zero squeaking noises anywhere until it rained again and the car dried out
9. went back two days ago to get them to regrease everything again
10. squeaking noise was there as soon as I left the parking lot
My conclusion is that, given that the only time when the noises subsided completely was when the rear strut assemblies were disassembled and reassembled, something inside the strut assemblies is making the noises, and every time it rains it just washes whatever grease was applied to wherever causing the very loud and noticeable squeaking noises.
I am out of ideas and about to get a second opinion from another shop cause this is insane.
__________________ [13-03, 11:25] MG1 when you hit the brakes, it shoots cum at pedestrian - bukkake
[12-03, 19:06] meme405 That e30 is so mexiflushed I thought we were in albuquerque
[12-03, 23:03] rb when i see a modded element. I have nothing but respect. either the parents kicked him out or the guy is killing hookers in the back
I told u like 15 times, poly bushing will always squeak. Change back to rubber if u don't like it LOL
Quote:
Originally Posted by Akinari
OK, so after the 5th time going to the shop that installed my coils to get rid of rear squeaking, there is still squeaking, and I'm like
Chronological order of events:
1. coils installed along with all new OEM parts everywhere, not a single old part was used
2. after driving for the first time in the rain about 2 weeks after installing the coils, squeaking started in the rear after the car dried out
3. went back to the shop got them to regrease everything
4. squeaking was there as soon as I left the shop parking lot
5. went back in for regreasing
6. squeaking happened again as soon as I left the shop parking lot
7. went back in for regreasing and they reassembled the rear strut assemblies
8. zero squeaking noises anywhere until it rained again and the car dried out
9. went back two days ago to get them to regrease everything again
10. squeaking noise was there as soon as I left the parking lot
My conclusion is that, given that the only time when the noises subsided completely was when the rear strut assemblies were disassembled and reassembled, something inside the strut assemblies is making the noises, and every time it rains it just washes whatever grease was applied to wherever causing the very loud and noticeable squeaking noises.
I am out of ideas and about to get a second opinion from another shop cause this is insane.
__________________
[23-07, 02:53] LSF22 the guy who i just saw had like 5 or 6 cars on his lawn needs a ride
[07-10, 15:42] nabs tbails14 = the legend continues
[27-10, 19:44] slickrick (to ts14) NO NOT THE EXHAUST
[07-10, 22:42] Ri2 If I had a real one I'd fap til it turns blue probably
[05-01, 16:24] Geoc ts you're a never ending inspiration for the inner buddy guy in all of us
I told u like 15 times, poly bushing will always squeak. Change back to rubber if u don't like it LOL
The only things in my rear suspension that are poly are my LCAs, which aren't making any of the noises I'm referring to. The sound is coming from the strut assemblies and I know it is because the only time the shop disassembled and reassembled my rear strut assemblies is when all the squeaking noises subsided until it rained again. Got nothing to do with the LCAs. Every single time the shop regreased everything it didn't help with the squeaking at all, only when the coils were taken out, disassembled/reassembled and put back in.
__________________ [13-03, 11:25] MG1 when you hit the brakes, it shoots cum at pedestrian - bukkake
[12-03, 19:06] meme405 That e30 is so mexiflushed I thought we were in albuquerque
[12-03, 23:03] rb when i see a modded element. I have nothing but respect. either the parents kicked him out or the guy is killing hookers in the back
Originally posted by v.b. can we stop, my pussy hurts... Originally posted by asian_XL fliptuner, I am gonna grab ur dick and pee in your face, then rub shit all over my face...:lol Originally posted by Fei-Ji haha i can taste the cum in my mouth Originally posted by FastAnna when I was 13 I wanted to be a video hoe so bad
RS.net, where our google ads make absolutely no sense!
Join Date: Apr 2013
Location: Squamish
Posts: 925
Thanked 2,300 Times in 556 Posts
Failed 7 Times in 7 Posts
Oh fun! That would drive me nuts. Not much I can do to diagnose/help without seeing it in person. It sounds like coil spring binding, but without seeing the assembly and having it move, so hard to determine what it is.
If you fancy a drive up to Squamish sometime this week, I'd be happy to see if I can't help solve it. I'm thinking we put it up on some axle stands and then manipulate the suspension with a jack while I can see/feel what's going on.
do you know what kind of grease is being used? maybe try another brand?
__________________ "The guy in the CR-V meanwhile, he'll give you a haughty glare. He's responsibly trying to lessen his impact, but there you go lumbering past him with your loud V8, flouting the new reality. You may as well go do some donuts in a strawberry patch and slalom through a litter of kittens." Dan Frio, Automotive Editor, Edmunds
Following up on this, turns out there was a bunch of mud caked on the inside of the wheels, it was smooth and pale enough that it didn't stand out until I started busting it off.
__________________ 1991 Toyota Celica GTFour RC // 2007 Toyota Rav4 V6 // 2000 Jeep Grand Cherokee
1992 Toyota Celica GT-S ["sold"] \\ 2007 Jeep Grand Cherokee CRD [sold] \\ 2000 Jeep Cherokee [sold] \\ 1997 Honda Prelude [sold] \\ 1992 Jeep YJ [sold/crashed] \\ 1987 Mazda RX-7 [sold] \\ 1987 Toyota Celica GT-S [crushed]
Quote:
Originally Posted by maksimizer
half those dudes are hotter than ,my GF.
Quote:
Originally Posted by RevYouUp
reading this thread is like waiting for goku to charge up a spirit bomb in dragon ball z
Quote:
Originally Posted by Good_KarMa
OH thank god. I thought u had sex with my wife. :cry:
Vehicle: 2007 VW GTI (MKV)
Issue: All fuses are hot (active 12V - not hot as in temperature) even when the key is out of the ignition.
Background: Before using an add-a-circuit for my dash cam (via power magic), I verified fuses that were always hot and fuses hot only when the ignition is on etc. After adding the dash camera into the fuse panel, the SRS light is now on and all fuses are hot. This isn't a big concern since it's not draining the battery. However, I want to tap into the fuse boxe for devices in the future and there is now a concern that there is no switched circuit available.
Looking to replace my passenger side axle the next time I have a couple days off. What is the best way to break axle nut loose? Huge breaker bar or rent an impact gun? Where can I rent impact guns for a decent price? Do they also rent out socket for the axle nut?
^ that's the better method, I usually jam a long bar between the wheel studs and against the ground, but I don't like doing it if the nut is really stuck.
__________________ 1991 Toyota Celica GTFour RC // 2007 Toyota Rav4 V6 // 2000 Jeep Grand Cherokee
1992 Toyota Celica GT-S ["sold"] \\ 2007 Jeep Grand Cherokee CRD [sold] \\ 2000 Jeep Cherokee [sold] \\ 1997 Honda Prelude [sold] \\ 1992 Jeep YJ [sold/crashed] \\ 1987 Mazda RX-7 [sold] \\ 1987 Toyota Celica GT-S [crushed]
Quote:
Originally Posted by maksimizer
half those dudes are hotter than ,my GF.
Quote:
Originally Posted by RevYouUp
reading this thread is like waiting for goku to charge up a spirit bomb in dragon ball z
Quote:
Originally Posted by Good_KarMa
OH thank god. I thought u had sex with my wife. :cry:
Finally got a video of this stupid thing. This is driving me absolutely INSANE. Can you believe that the rear suspension creaks even when I'm opening and shutting my door? It's like even the most minute of movements will cause the rear suspension to creak.
I emailed tein, they said it shouldn't be a noise that the strut assemblies should make internally and it sounds more like some other suspension component that's making the noise. HOWEVER, they said the only thing it could be that's internal making the noise is the rubber spring seats. Which leads me to the conclusion that it probably is that, because the shop I get my work done greased up all the other suspension components 4 separate times without getting rid of the noise, but the ONE time they took apart the coil, reassembled them and stuck it back on was the ONLY time the noise was gone entirely. Until it rained again.
it's also pretty fucking embarrassing because the noise is even louder from the outside and all people hear is just a squeaky creaky lunchbox on wheels, driving me nuts because I replaced every single possible suspension part I could replace with OEM Honda parts and brand new tein suspension.
You check if the door hinges are lubed up and the bolts to the black door stopper rod is tight?
Quote:
Originally Posted by Akinari
Finally got a video of this stupid thing. This is driving me absolutely INSANE. Can you believe that the rear suspension creaks even when I'm opening and shutting my door? It's like even the most minute of movements will cause the rear suspension to creak.
I emailed tein, they said it shouldn't be a noise that the strut assemblies should make internally and it sounds more like some other suspension component that's making the noise. HOWEVER, they said the only thing it could be that's internal making the noise is the rubber spring seats. Which leads me to the conclusion that it probably is that, because the shop I get my work done greased up all the other suspension components 4 separate times without getting rid of the noise, but the ONE time they took apart the coil, reassembled them and stuck it back on was the ONLY time the noise was gone entirely. Until it rained again.
it's also pretty fucking embarrassing because the noise is even louder from the outside and all people hear is just a squeaky creaky lunchbox on wheels, driving me nuts because I replaced every single possible suspension part I could replace with OEM Honda parts and brand new tein suspension.
Ok so my car is at the shop and the drivetrain is out, I'm getting a pile of new parts put on (gaskets, all hoses, all three pumps, timing belt, clutch, cams, etc etc etc) and they're asking if I want to do the headgasket and studs while it's this far apart. I'm thinking of skipping it, because I don't like cracking open a perfectly good motor, and if I do I'd want to do rings and bearings as well. Car currently has 180k and perfect compression, the turbo is staying stock and the boost will only be upped from 11-12 psi to 16 psi on occasions.
Thoughts?
__________________ 1991 Toyota Celica GTFour RC // 2007 Toyota Rav4 V6 // 2000 Jeep Grand Cherokee
1992 Toyota Celica GT-S ["sold"] \\ 2007 Jeep Grand Cherokee CRD [sold] \\ 2000 Jeep Cherokee [sold] \\ 1997 Honda Prelude [sold] \\ 1992 Jeep YJ [sold/crashed] \\ 1987 Mazda RX-7 [sold] \\ 1987 Toyota Celica GT-S [crushed]
Quote:
Originally Posted by maksimizer
half those dudes are hotter than ,my GF.
Quote:
Originally Posted by RevYouUp
reading this thread is like waiting for goku to charge up a spirit bomb in dragon ball z
Quote:
Originally Posted by Good_KarMa
OH thank god. I thought u had sex with my wife. :cry:
Ok so my car is at the shop and the drivetrain is out, I'm getting a pile of new parts put on (gaskets, all hoses, all three pumps, timing belt, clutch, cams, etc etc etc) and they're asking if I want to do the headgasket and studs while it's this far apart. I'm thinking of skipping it, because I don't like cracking open a perfectly good motor, and if I do I'd want to do rings and bearings as well. Car currently has 180k and perfect compression, the turbo is staying stock and the boost will only be upped from 11-12 psi to 16 psi on occasions.
Thoughts?
it really depends.. how much money are you saving if they do this while its all apart? when you get into removing the head, rings, and bearings, the motor will be pulled out of the vehicle while its not necessary for the work you already have lined up (im not familiar with the celica motor so maybe im wrong).
if your compression numbers are good, I wouldn't be concerned at this time
The motor has to come out for the power steering system leaks and clutch so it's already out and torn down to a block + head with the lower rotating assembly and valves. To do it now I'm looking at an extra ~$2-2.5k with new pistons or $1-1.5k without, if I do it later the car would be off the road for a while as I'd pull the motor myself (it's a big job).
__________________ 1991 Toyota Celica GTFour RC // 2007 Toyota Rav4 V6 // 2000 Jeep Grand Cherokee
1992 Toyota Celica GT-S ["sold"] \\ 2007 Jeep Grand Cherokee CRD [sold] \\ 2000 Jeep Cherokee [sold] \\ 1997 Honda Prelude [sold] \\ 1992 Jeep YJ [sold/crashed] \\ 1987 Mazda RX-7 [sold] \\ 1987 Toyota Celica GT-S [crushed]
Quote:
Originally Posted by maksimizer
half those dudes are hotter than ,my GF.
Quote:
Originally Posted by RevYouUp
reading this thread is like waiting for goku to charge up a spirit bomb in dragon ball z
Quote:
Originally Posted by Good_KarMa
OH thank god. I thought u had sex with my wife. :cry:
Recently started noticing this screeching, high-pitched grinding/whining sound on cold starts.
This happens when i pop it to first, and when i'm at that balance where my foot is still slightly on the clutch and i'm gassing to go ahead. Essentially, the sound happens when i'm gassing while still letting go of the clutch. Sounds pretty loud esp on inclines. This also happens on reverse. Doesn't seem to happen after the car warms up. Sounds like its coming from the tranny.
Any ideas?